11:52 am
![Avatar](https://posse4x4.org/wp-content/sp-resources/forum-avatars/1427135142Profile-Small.jpeg)
![](https://posse4x4.org/wp-content/sp-resources/forum-badges/Officer-Badge.png)
Club Trailmaster
March 13, 2015
![sp_UserOfflineSmall](https://posse4x4.org/wp-content/sp-resources/forum-themes/unified/images/sp_UserOfflineSmall.png)
Here is the deal, have a bunch of stuff taking up room in my shop I need to move to get my lift and pallet racking installed. Posse gets first run at everything so make me a reasonable offer and it’s yours.
Jeep parts:
TJ:
-RE 3.5” springs
-Rubicon factory fender flares (wider than sport) fronts need minor attention with a heat gun
-K&N cold air intake
-RE front radius arms
LJ:
-Factory rubicon rock rails with gaskets( can be trimmed to length for a TJ)
Jk:
-3.5” RE lift springs - 6k miles
-3.5” RE mono tube shocks - 6k miles
-3.5” RE twin tube shocks - 30k miles
-RE rear CV driveshaft- for JKU 4k miles
-RE front sway bar disconnects and rear swaybar link extensions for 3.5” lift
-RE front and real fixed lower control arms - 6k miles
-RE rear upper adjustable control arms - 6k miles
-front and rear 2” bump stop extensions
-axle mount high steer bracket for trac bar
-rear track bar bracket (for 2-6” lift)
-new in box RE forged adjustable front trac bar
-weld on C-gussets
-new in box teraflex ball joints
-front and rear JKU factory driveshafts (rear needs boot replaced)
-new 1350 rear axle yoke
-2 new in box precision hubs with ABS sensors
-Curt bolt on class 3 hitch
-adjustable spare tire spacer
-used Bushwhacker flat fenders for JKU
-4 spidertrax 1.5” wheel spacers (2 new in box, 2 run for 1k miles)
-AEV d44 diff cover
JL
-front factory control arms upper and lower
-2 sets factory rubicon rockers
-factory sport take off wheels and tires, low tread basically rollers no TPMS
JT
-sport take off tires and wheels, low tread rollers, no TPMS
-Rubicon AT3 take off wheels and tires with early TPMS sensors, 2/3 tread
-Rear under seat lock box
Tools:
-Franklin rolling scaffolding, 1 set of risers, 2 sets of crossbars and platforms
-14” metal chop saw Craftsman
-Delta 10” wood chop saw
-scroll saw
-tile saw
Misc vehicle parts:
-Reese 16k Kwik slide 5th wheel hitch
-timbren 3500lb trailer axle (jeep trailer width)
More to come as I uncover more goodies.
8:15 am
![Avatar](https://posse4x4.org/wp-content/sp-resources/forum-avatars/1408842406image.jpg)
![](https://posse4x4.org/wp-content/sp-resources/forum-badges/Member-Badge.png)
Club Member
February 26, 2014
![sp_UserOfflineSmall](https://posse4x4.org/wp-content/sp-resources/forum-themes/unified/images/sp_UserOfflineSmall.png)
10:52 am
![Avatar](https://posse4x4.org/wp-content/sp-resources/forum-avatars/1427135142Profile-Small.jpeg)
![](https://posse4x4.org/wp-content/sp-resources/forum-badges/Officer-Badge.png)
Club Trailmaster
March 13, 2015
![sp_UserOfflineSmall](https://posse4x4.org/wp-content/sp-resources/forum-themes/unified/images/sp_UserOfflineSmall.png)
7:25 am
![Avatar](https://posse4x4.org/wp-content/sp-resources/forum-avatars/1589909071Flex.jpg)
![](https://posse4x4.org/wp-content/sp-resources/forum-badges/Officer-Badge.png)
Club Webmaster
August 5, 2017
![sp_UserOfflineSmall](https://posse4x4.org/wp-content/sp-resources/forum-themes/unified/images/sp_UserOfflineSmall.png)
I'm interested in the sway bar disconnects. The precision Hubs, your talking about the unit bearing assembly right? If yes I am thinking I should take them and carry as a trail spare for the club.
Gives me a good reson to cruise over and check progress on the shop, approx 5 miles as the crow flies but a 30 minute drive... #countryproblems.
K6NUB
![sp_BirthdayIcon](https://posse4x4.org/wp-content/sp-resources/forum-plugins/birthdays/resources/images/sp_BirthdayIcon.png)
![sp_Information](https://posse4x4.org/wp-content/sp-resources/forum-themes/unified/images/sp_Information.png)